This article in the next paragraphs about How to Install a Bathtub Yourself is amazingly enlightening. Don't miss it.
Mounting a bathtub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and also often, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably difficult job. If the old tub is easily accessible, the job can move rapidly; if you have to open a wall surface to eliminate the old tub and also position the brand-new tub, the job is a lot harder. In either case, the job is within a home handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Make sure you have actually qualified on your own for the job as well as are comfortable attempting it. As opposed to employing a contractor to take control of a halfway-completed project, it is far better to think about using one before you start. Chances are you might need an expert plumber to make tube links.
This short article will certainly help you set up a brand-new tub in your washroom if you have currently acquired a new bathtub and don't require to change the plan of your previous water pipes.
Your tools and also material checklist need to comprise the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, after that the first thing you should do is separate the supply of water. After doing so, activate the faucets to drain any water staying in the system. The process of eliminating the existing faucets can be quite troublesome because of the limited accessibility that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the faucets. Have a towel all set for the remaining water that will come from the pipelines. As soon as the supply pipelines have actually been removed, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from turning during this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the various other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin guaranteeing that the washers are in area in between the faucet as well as the sink. Protect the tap in place with the supplier given backnut. As soon as the faucet is safely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet ports. The former type needs to be attached to the tap ends first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Tub
Using both wood boards under its feet, put the bathtub in the called for setting. The wooden boards are helpful in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 little points.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bath tub up until the spirit level reviews level.
To mount faucets, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; after that do the same for the various other tap.
Switch on the water system and examine all joints as well as brand-new pipework for leaks and also tighten them if needed. Fill the tub and additionally check the overflow electrical outlet and the regular outlet for leakages.
Lastly, deal with the bath paneling as described in the maker's instruction manual. Tiling as well as sealing around the tub needs to wait up until the bath tub has been utilized at the very least once as this will certainly settle it right into its final setting.
Preparing for the Setup
To start with, the supporting structure provided with the bath needs to be fitted (if required) according to the maker's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to ensure that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop strain on the tub.
Fit the adaptable faucet connectors to the bottom of the two faucets using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you make use of all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its final setting.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to break a stiff seal, triggering the water to permeate the wall between the bath and the tiling, leading to complications with dampness and possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your components and also fittings. They are sold in tubes and cartridges, and can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to always fill the bath tub with water prior to securing, to enable the motion experienced when the tub is in usage. The sealer can split relatively early if you do not consider this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise quickly available on the marketplace. It is recommended to fit the tiles making use of water-resistant or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I found that content about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while doing a lookup on the internet. Do you know about somebody else who is curious about the subject? Please feel free to promote it. Thanks a lot for taking the time to read it.
Click Here To Find Out More